LED
State
Green
Description
The correct cable is connected to the interface and
the connected equipment has power
QuickStart Guide
Ports 1 and 2 Left
FortiDB-2000B
Flashing Network activity at this interface.
Amber
Ports 1 and 2 Right
Ports 3 and 4 Left
Green
The correct cable is connected to the interface and
the connected equipment has power.
Flashing Network activity at this interface.
2000B
Green
Amber
Off
The interface is connected at 1000 Mbps.
The interface is connected at 100 Mbps.
The interface is connected at 10 Mbps.
Ports 3 and 4 Right
Visit these links for more information and documentation for your Fortinet product.
© Copyright 2009 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trademarks
of their respective holders.
Regulatory Compliance
FCC Class A Part 15 CSA/CUS
27 January 2009
15-32000-85972-20090127
Package Contents
Connector
Type
Speed
Protocol
Description
Copper gigabit connection to 10/100/1000 copper networks.
Ports 1 to 4
RJ-45
10/100/1000
Base-T
Ethernet
CONSOLE
USB
DB9
USB
9600 8/N/1
RS-232 serial Optional connection to the management computer. Provides access to
the command line interface (CLI).
USB
For diskless boot.
2000B
QuickStart Guide
2000B
Copyright 2008 Fortinet Inco
Trademarks
Welcome
|
Bienvenue | Willkommen | 歓
迎
|
Bienvenido
|
Benvenuto
Redundant
Console
connection
USB
Ethernet
ports
power supply
DB-9 Serial Cable
Power Cables
Straight-through
Ethernet cable
2 Mounting Slide Rails
Connecting
Connect the following to the FortiDB unit. Ensure the FortiDB unit is placed on a stable surface or install in a standard 19 inch rack. See the
FortiDB-2000B Rack Install Guide for details.
•
•
•
•
Insert an Ethernet cable to port 1.
Connect the other end of network cable to the network hub or switch.
Connect the AC Power Cord to the Power Supply.
Connect the Power Cord to a surge protected
power bar or power supply.
•
Remove the front panel and press the power button.
When powering off the FortiDB unit, always shut down the unit using the fol-
lowing procedures before disconnecting the power supply. Not following this
procedure can increase the risk of damaging the FortiDB hard disk.
Redundant
power supply
Console
Ethernet
ports
USB
You can only shut down the FortiDB unit using the CLI.
Enter the following command at the prompt:
connection
execute shutdown
To power down completely, remove the front panel and press the power button.
Configuration Tools
Web-based manager
Command Line Interface (CLI)
The FortiDB web-based manager is an easy-to-use management tool.
Use it to configure the administrator password, the interface and default gateway addresses,
add Fortinet devices and configure reports.
The CLI is a full-featured management tool. Use it to configure the administrator password,
the interface addresses, the default gateway address, and the DNS server addresses. To
configure advanced settings, see the Tools and Documentation CD included with the
FortiDB unit.
Requirements:
•
•
An Ethernet connection between the FortiDB unit and management computer.
A web browser such as FireFox or Internet Explorer on the management computer.
Requirements:
•
•
The DB9 serial connection between the FortiDB unit and management computer.
A terminal emulation application (HyperTerminal for Windows) on the management
computer.
|
Conair Washer CS19VCSIB 9786 User Manual
Cooper Lighting Indoor Furnishings 132T8 User Manual
Desa Tech Indoor Fireplace CHDV37N User Manual
Dukane Whiteboard Accessories LB77HA User Manual
Edelbrock Automobile Parts 15017 User Manual
Everpure Water System 7DM User Manual
Fluke Landscape Lighting 335D User Manual
Frigidaire Washer FAFW3517A User Manual
GE DVD VCR Combo DVMRe User Manual
Gitzo Camcorder Accessories G1411 User Manual